As an Amazon Associate I earn from qualifying purchases.1. KeeYees
KeeYees Pro Micro ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino Pack of 3pcs
KeeYees - Just connect to the on-board micro-usb connector for programming. The pro micro board can be powered via the micro USB connection or with an external power supply. Atmega32u4 running at 5v/16mhz, maximum voltage on the RAW pin is 9V, recommended voltage 6-7V.
Supported by ard ide v1. 01; 4 x 10-bit adc pins, 12 x digital I/Os; Rx and Tx Hardware Serial Connections. If this module cannot be recognized by your computer, please refer to this link to install the driver.
| Brand | KeeYees |
| Manufacturer | KeeYees |
| Height | 8 cm (3.15 Inches) |
| Length | 10 cm (3.94 Inches) |
| Width | 9 cm (3.54 Inches) |
| Part Number | KYES8-196-3 |
2. KeeYees
KeeYees Pro Micro ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino Pack of 1pcs
KeeYees - Atmega32u4 running at 5v/16mhz, maximum voltage on the RAW pin is 9V, recommended voltage 6-7V. If this module cannot be recognized by your computer, please refer to this link to install the driver.
The pro micro board can be powered via the micro USB connection or with an external power supply. Just connect to the on-board micro-usb connector for programming. Supported by ard ide v1. 01; 4 x 10-bit adc pins, 12 x digital I/Os; Rx and Tx Hardware Serial Connections.
3. AITRIP
AITRIP 5 pack PRO Mini Atmega328P-AU 5V/16MHz Development Board Microcontroller Bootloadered with Pin Headers for Arduino 5PCS
AITRIP - Support serial Download, 5V/16M. 8 analog inputs ports: A0 ~ A7. Size: 33. 8mm x 18mm. Support external power supply 3. 8-12v dc. Main chip: atmel Atmega328P-AU.
4. AITRIP
AITRIP 5PCS for Arduino Mini Nano V3.0 ATmega328P 5V 16M Micro Controller Board Module for ArduinoIDE 5PCS
AITRIP - It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper. The power source is automatically selected to the highest voltage source. The nano can be powered via the mini-b usb connection, 7-12V unregulated external power supply pin 30, or 5V regulated external power supply pin 27.
Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, GND on one top, so users have more breadboard space.
The nano is using the chips atmega328P and CH340, Replace FT232RL. It's got a pin layout that works well with the Mini or the Basic Stamp TX, ATN, RX, power and ground on the other.
The nano can be powered via the mini-b usb connection, 7-12V unregulated external power supply pin 30, or 5V regulated external power supply pin 27. The power source is automatically selected to the highest voltage source. It is a smallest, complete, and breadboard friendly board.
5. AITRIP
AITRIP 2PCS Pro Micro ATmega32U4 5V 16MHz Type-C Development Module Board with 2 Row pin Header Compatible ard-uino Leonardo Replace Pro Mini
AITRIP - 4 x 10-bit adc pins, 12 x Digital I/Os. On-board type-C connector for programming. Atmega32u4 running at 5V/16MHz. Supported by IDE v1. 01. Rx and tx hardware Serial Connection.
6. SparkFun
Arduino Pro Mini 328-5V/16MHzNew
SparkFun - Arduino pro mini 328 - 5V/16MHzNew. It's blue! it's thin 08mm! it's the arduino Pro Mini! Minimal design approach to Arduino.
| Brand | SparkFun |
| Manufacturer | SparkFun |
| Height | 1 cm (0.39 Inches) |
| Length | 6 cm (2.36 Inches) |
| Width | 10 cm (3.94 Inches) |
| Part Number | DEV-11113 |
| Model | DEV-11113 |
7. AITRIP
AITRIP 4PCS Pro Micro ATmega32U4 5V 16MHz Type-C Development Module Board with 2 Row pin Header Compatible ard-uino Leonardo Replace Pro Mini
AITRIP - On-board type-C connector for programming. Rx and tx hardware Serial Connection. 4 x 10-bit adc pins, 12 x Digital I/Os. Atmega32u4 running at 5V/16MHz. Supported by IDE v1. 01.
8. ZHITING
ZHITING 3PCS Pro Micro,for ATmega32U4 5V 16MHz Micro USB Development Board Module Microcontroller for Arduino IDE Development Board Microcontroller
ZHITING - This board connects directly to the FTDI Basic Breakout board and supports auto-reset. Supported by arduino ide v1. 01; 4 x 10-bit adc pins, 12 x digital I/Os; Rx and Tx Hardware Serial Connections.
On-board micro-USB connector for programming. Pay attention to : 1. When you open the arduino ide software, could you please go to the tool and choose the board "Arduino Leonardo". Atmega32u4 running at 5v/16mhz, maximum voltage on the RAW pin is 9V, recommended voltage 6-7V.
9. Arduino
Arduino Micro with Headers A000053
Arduino - It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. The power source is selected automatically.
The micro can be powered via the micro USB connection or with an external power supply. It has a form factor that enables it to be easily placed on a breadboard. The micro board is similar to the arduino Leonardo in that the ATmega32U4 has built-in USB communication, eliminating the need for a secondary processor.
The micro is a microcontroller board based on the ATmega32U4 datasheet, developed in conjunction with Adafruit. It has 20 digital input/output pins of which 7 can be used as PWM outputs and 12 as analog inputs, a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button.
| Brand | Arduino |
| Manufacturer | Arduino |
| Height | 7.62 cm (3 Inches) |
| Length | 10.16 cm (4 Inches) |
| Weight | 0 kg (0.01 Pounds) |
| Width | 2.54 cm (1 Inches) |
| Part Number | A000059 |
| Model | ARD-A000059 |
KeeYees - Just connect to the on-board micro-usb connector for programming. The pro micro board can be powered via the micro USB connection or with an external power supply. Atmega32u4 running at 5v/16mhz, maximum voltage on the RAW pin is 9V, recommended voltage 6-7V. Supported by ard ide v1. 01; 4 x 10-bit adc pins, 12 x digital I/Os; Rx and Tx Hardware Serial Connections. If this module cannot be recognized by your computer, please refer to this link to install the driver.
AITRIP - Support serial Download, 5V/16M. 8 analog inputs ports: A0 ~ A7. Size: 33. 8mm x 18mm. Support external power supply 3. 8-12v dc. Main chip: atmel Atmega328P-AU.
AITRIP - It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper. The power source is automatically selected to the highest voltage source. The nano can be powered via the mini-b usb connection, 7-12V unregulated external power supply pin 30, or 5V regulated external power supply pin 27.
AITRIP - 4 x 10-bit adc pins, 12 x Digital I/Os. On-board type-C connector for programming. Atmega32u4 running at 5V/16MHz. Supported by IDE v1. 01. Rx and tx hardware Serial Connection.
SparkFun - Arduino pro mini 328 - 5V/16MHzNew. It's blue! it's thin 08mm! it's the arduino Pro Mini! Minimal design approach to Arduino.
AITRIP - On-board type-C connector for programming. Rx and tx hardware Serial Connection. 4 x 10-bit adc pins, 12 x Digital I/Os. Atmega32u4 running at 5V/16MHz. Supported by IDE v1. 01.
ZHITING - This board connects directly to the FTDI Basic Breakout board and supports auto-reset. Supported by arduino ide v1. 01; 4 x 10-bit adc pins, 12 x digital I/Os; Rx and Tx Hardware Serial Connections. On-board micro-USB connector for programming. Pay attention to : 1. When you open the arduino ide software, could you please go to the tool and choose the board "Arduino Leonardo". Atmega32u4 running at 5v/16mhz, maximum voltage on the RAW pin is 9V, recommended voltage 6-7V.
Arduino - It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. The power source is selected automatically.
